no image available
3" - 75mm - Vacuum System 1 1/4" x 8tpi VS3H125
Vacuum chucking is a very popular method of mounting bowls on the lathe for light turning and finishing without marking the surface of the work.The Holdfast Vacuum Chuck System is a new generation of Vacuum Chuck that runs off of a standard shop air compressor (minimum 2.5 fm at 55-65psi) using the V810R Vacuum Generator.The Holdfast System offers simplicity, dependability, and performance at a fraction...
£249.00
3" - 75mm - Vacuum System 1 1/4" x 8tpi
3" - 75mm - Vacuum System 1 1/4" x 8tpi
Ferrules for all Robert Sorby tools are available as accessories. Woodturning and carving tool ferrules are brass. Smaller woodworking chisel ferrules are also brass but larger timber framing chisels and slicks are steel. Size and codes for all handles and ferrules can be seen below.
£0.75

3" - 75mm - Vacuum System 1" x 8tpi
3" - 75mm - Vacuum System 1" x 8tpi
Ferrules for all Robert Sorby tools are available as accessories. Woodturning and carving tool ferrules are brass. Smaller woodworking chisel ferrules are also brass but larger timber framing chisels and slicks are steel. Size and codes for all handles and ferrules can be seen below.
£0.50
3" - 75mm - Vacuum System 1" x 8tpi
3" - 75mm - Vacuum System 1" x 8tpi
Ferrules for all Robert Sorby tools are available as accessories. Woodturning and carving tool ferrules are brass. Smaller woodworking chisel ferrules are also brass but larger timber framing chisels and slicks are steel. Size and codes for all handles and ferrules can be seen below.
£0.60

no image available
3" - 75mm - Vacuum System 33 x 3.5 VS3H33
Vacuum chucking is a very popular method of mounting bowls on the lathe for light turning and finishing without marking the surface of the work.The Holdfast Vacuum Chuck System is a new generation of Vacuum Chuck that runs off of a standard shop air compressor (minimum 2.5 fm at 55-65psi) using the V810R Vacuum Generator.The Holdfast System offers simplicity, dependability, and performance at a fraction...
£249.00
3" - 75mm - Vacuum System 33 x 3.5
3" - 75mm - Vacuum System 33 x 3.5
Ferrules for all Robert Sorby tools are available as accessories. Woodturning and carving tool ferrules are brass. Smaller woodworking chisel ferrules are also brass but larger timber framing chisels and slicks are steel. Size and codes for all handles and ferrules can be seen below.
£1.40

Compatriot Chuck
Compatriot Chuck RSPCCOM
The versatility of the Patriot chuck is demonstrated by its availability without jaws in three formats. Known as the Compatriot chuck these are the: RSPCOM, RSPCOMN34 and RSPCOMMH. Jaws from other chuck manufacturers fit this system but please contact Robert Sorby to be sure of appropriate fittings.
£128.15
Patriot Chuck
Patriot Chuck RSPC
Like all Robert Sorby tools the Patriot is proudly manufactured in Britain. Fitted with smooth action 2" (50mm) jaws which have internal and external dovetail and gripper teeth to ensure work is held more securely. It also supplied with a screw chuck and an insert* which enable it to fit the vast majority of woodworking lathes.
£176.00

Patriot Deep Grip Jaws
Patriot Deep Grip Jaws RSJDG
Designed with deep sides to give extra grip on large logs and awkward pieces of wood.They also have a large internal and external dovetail to securely hold large bowls in excess of 16" diameter.
£61.25
Patriot Drive Centre
Patriot Drive Centre RSPDC
A simple but effective 4 prong drive centre that fits directly on to the jaws of the chuck.
£16.25

Patriot Long Nose Jaws
Patriot Long Nose Jaws RSJLN
Rough turned bowls can be remounted internally with the reach of almost 4" of these jaws.Extra access to the back of a turned piece is acquired due to the tapered shape and the dovetail being 2" away from the chuck body.
£72.75
Pen Blank Drilling Jaws
Pen Blank Drilling Jaws PBDJ
These Jaws will hold your pen blank central so you can drill on the lathe.A groove in both jaws ensure you have a tight secure grip of the pen blank.Mount your drill chuck into your tailstock and simply wind in the drill.With these jaws being mounted on a lathe, you have more control over the speed of the motor and a much better control of the feed speed.These jaws have been designed to fit a Robert...
£27.20

Pin Jaws For Viper 2
Pin Jaws For Viper 2 V2PJ
Pin Jaws for Viper2 Chuck.Set of 4 optional jaws for Viper2 geared scroll chuck.Pin jaws allow smaller pieces to held than the standard jaws.The inside is smooth and parallel, the outside is serrated for maximum grip.The jaws project 29mm from the base plate.Expands from22mm to 46mmContracts from32mm to 8mm
£15.00
Spindle Adaptor 1.25-8 F 1 x 8 M
Spindle Adaptor 1.25-8 F 1 x 8 M A866
Spindle Adapters have a hole for vacuum applications. Can be used on standard non-vacuum chuck heads. Flats on extenders allow for easy removal with wrench if necessary. Each adapter includes two No Lock Spindle Washers 1 1/4" x 8tpi F to 1" x 8tpi M
£38.95

Spindle Adaptor 33M F 1.25 x 8 M
Spindle Adaptor 33M F 1.25 x 8 M A869
Spindle Adapters have a hole for vacuum applications. Can be used on standard non-vacuum chuck heads. Flats on extenders allow for easy removal with wrench if necessary. Each adapter includes two No Lock Spindle Washers 33i F to 1 1/4" x 8 M
£38.95
Spindle Extender 1" x 8tpi
Spindle Extender 1" x 8tpi A861
Extenders allow deep bowls to be turned without hitting the lathe. A hole through the center allows vacuum to go through center of extenders. Can be used on standard non-vacuum chuck heads. Flats on extenders allow easy removal with wrench if necessary.Each extender includes two No Lock 1" x 8tpi
£44.95

Spindle Extender 1.125 x 8tpi
Spindle Extender 1.125 x 8tpi A862
Extenders allow deep bowls to be turned without hitting the lathe. A hole through the center allows vacuum to go through center of extenders. Can be used on standard non-vacuum chuck heads. Flats on extenders allow easy removal with wrench if necessary.Each extender includes two No Lock 1 1/4" x 8tpi
£44.95
Steb DriveSteb Drive
Steb Drive STBCHUCK
The Steb Drive uses the same innovatively designed head as the original Stebcentre.The Steb Drive is designed to fit into the jaws of the majority of 4 jaw woodturning chucks available.It has a positive and secure location utilising the flats of the spigot.
from £42.40

V812 Vacuum Generator
V812 Vacuum Generator V812
Vacuum generator for the stabilising system and vacuum chucks.
£157.50
Vacuum Adapter Kit
Vacuum Adapter Kit V802
Holdfast Vacuum Chuck Adaptor Kit
£53.50

Viper 2 - Dovetail Jaws
Viper 2 - Dovetail Jaws V2DJ
Dovetail Jaws, serrated inside for Viper2 Chuck.Set of 4 optional jaws for our Viper2 scroll chuck. These jaws are deeper than the standard dovetails jaws supplied with new chucks. The inside is parallel and serrated for maximum grip, 25mm deep. The outside is dovetailed and projects 16mm from the base plate. Expands from 38mm to 62mm Contracts from 54mm to 30mm
£15.00
Viper Chuck 2 3/4" Diameter
Viper Chuck 2 3/4" Diameter VIPER2
4 Jaw Scroll Chuck for wood lathes.Part of the new Viper range from Charnwood.A compact scroll chuck, with the jaws adjusted by a geared mechanism for simple one handed operation.Self centering, high precision design.Ideal for Mini and Midi sized lathes.The standard dovetail jaws can grip the workpiece both internally or externally depending on the style and shape of the piece to be turned.The chuck...
£99.00

Wide Jaws For Viper 2
Wide Jaws For Viper 2 V2WJ
Wide Jaws for Viper2 Chuck.Set of 4 optional jaws for Viper2 geared scroll chuck.The Wide jaws have a serrated edge both internally and externally and can grip much larger pieces than the standard jaws.Projects 13mm from base plate.Expands from70mm to 94mmContracts from82mm to 58mm
£15.00
Wobble Chuck
Wobble Chuck RSWC
An inexpensive introduction to off-centre or eccentric turning, the Wobble Chuck fits in the standard 2" jaws of the Patriot chuck in the same manner as a faceplate ring.The workpiece can be held by three screws - like a faceplate - or by a single wood screw - like a screw chuck - or by both means.It is then off-set by rotating the upper section of the Wobble Chuck.Ideal for goblets with off-set stems.A...
£66.85
Page: 1 | 2 | 3 |